NEO ISOLIERFARBE
    SEALANT
    PRODUCT CODE: IF00
    TECHNICAL DATA SHEET NO. 04-Repair & Renovation
    JULY 2009

  1. Product Description

    NEO Isolierfarbe is a quick drying sealant for the sealing of previously stained areas to prevent the stains bleeding through the water or solvent based top coat. Because of NEO Isolierfarbe’s outstanding penetration it gives excellent bonding adhesion of itself and subsequent topcoats.
  2. Application Areas

    • Interior and exterior use.
    • Previously painted areas which are water, nicotene or soot stained. Seal off before repainting can commence.
  3. Product Features

    • Quick drying.
    • Excellent sealer for water stains on ceilings.
    • Can be used to seal off old, deteriorated bitumen and tar substrates and roofing felt.
    • Excellent adhesion to a range of surfaces including tempered hardboard/fibre-boards which are notoriously difficult to overcoat.
    • Can be over-coated with a wide range of NEO Paints’ water and solvent based topcoats.
  4. Product Data

    Resin Base Air drying synthetic solution polymer
    Drying Time Touch dry: 15-20 minutes
    Hard dry: 1 - 2 hours
    Solid Matter by Content By volume: 30-32%
    By mass: 55-57%
    Film Thickness 40 microns
    Spreading Rate 5 – 8 square metres per litre.
    Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 5-6 square metres per litre for the first coat and 7-8 square metres per litre for subsequent coats and when applied to sealed, previously painted substrates.
    Surface Appearance Semi matt
  5. Application Details

    • Mixing Always stir well before use with a flat paddle.
    • Application Method Brush or roller. 
    Spray application is NOT possible.
    • Thinning NEO M-Thinners (mt01).
    • Cleaning NEO M-Thinners (mt01).
    • Application • Stir well before use.
    • Spray application is NOT possible.
    • Normally only one coat of NEO Isolierfarbe is required, however, for severely stained surfaces two coats may be required.
    • Apply a generous coat of NEO Isolierfarbe with brush or roller.
    • Allow to dry 2 hours before applying topcoat.
    • Can be over-coated with NEO Paints’ water or solvent based products.
    • Only apply in well ventilated areas, keep away from all ignition sources, flames and sparks.
    • Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 5-6 square metres per litre for the first coat and 7-8 square metres per litre for subsequent coats and when applied to sealed, previously painted substrates.
    • Do not eat, drink or smoke while applying.
    • Do not apply before 09:00 and after 16:00 in the winter.
    • Clean up application equipment with NEO M-Thinners (mt01).
    • For thinning use NEO M-Thinners (mt01).
  6. Surface Preparation

    • New or Stained surfaces, including Bitumen and Tar products • Only apply to dry substrates where the moisture content is less than 15%.
    • Remove all dust, loose particles, flaking and peeling coatings from the substrate; if soot or nicotine stains are present wash them off with hot soapy water.
    • Allow to dry.
    • Normally only one coat of NEO Isolierfarbe is required, however, for severely stained surfaces two coats may be required.
    • Spray application is NOT possible.
    • Apply a generous coat of NEO Isolierfarbe with brush or roller.
    • Allow to dry 2 hours before applying topcoat.
  7. Colour Range and Quantities

    • NEO Isolierfarbe is available in White only.
    • Available in 1 litre and 5 litres.
  8. Precautions

    • NEO Isolierfarbe is flammable.
    • Use only in well ventilated areas.
    • Avoid inhaling of solvent vapours.
    • Do not eat, drink or smoke while applying.
    • Do not apply to extremely alkaline substrates like fibre cement.
  9. Disclaimer

    NEO Paints can not be held liable if the product fails due to improper surface preparation or application.