NEO WOODCOATING
    EXTERIOR SUEDE VARNISH
    PRODUCT CODE: WC01
    TECHNICAL DATA SHEET NO. 05-Lacquers & Varnishes
    JULY 2009

  1. Product Description

    NEO Woodcoating (exterior suede) is a highly flexible and UV light resistant modified alkyd based, exterior varnish containing special UV absorbers/pigments developed for wooden substrates. The coating dries to a semi matt finish.
    NEO Woodcoating can be applied on any type of exterior woodwork and will last for years in the harsh Namibian climate.
    NEO Woodcoating contains iron oxide pigments and therefore, has a light yellow shade.
    This product is not suitable for use on floors, being too soft and not sufficiently wear resistant.
  2. Application Areas

    Interior and exterior use.
    Properly prepared wooden or timber substrates.
  3. Product Features

    High UV and water resistance for the harsh Namibian interior and coastal climates.
    Flexible - moves with the wood but does not gather dust.
    Excellent adhesion to properly prepared wooden substrates.
    NEO Woodcoating dries rather slowly and recoating is possible only after at least 24 hours.
    The application of three coats is recommended for use on new untreated wood.
  4. Product Data

    Resin Base Alkyd resin
    Drying Time Touch dry: 6-8 hours
    Hard dry: 24+ hours
    Solid Matter by Content By volume: 44%
    By mass: 52%
    Film Thickness 20-25 microns
    Spreading Rate 6-12 square metres per litre.
    Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 6-8 square metres per litre for the first coat and 10-12 square metres per litre for subsequent coats and when applied to sealed substrates.
    Surface Appearance Semi matt
  5. Application Details

    Mixing Always stir well before use with a flat paddle.
    Application Method Brush application. 
    Paint roller application is not recommended.
    Thinning NEO Mineral Turpentine (mt00).
    Cleaning NEO Mineral Turpentine (mt00).
    Application Stir well before use.
    Sand the wooden substrate well and remove all dust.
    Three coats of NEO Woodcoating are applied for best results.
    Brush apply the first coat diluted 10% with NEO Mineral Turpentine (mt00).
    Allow to dry 18-24 hours before sanding again.
    Remove all dust.
    Brush apply two more generous coats leaving 24 hours between coats.
    Clean up application equipment with NEO Mineral Turpentine (mt00).
    Only apply in well ventilated areas, keep away from all ignition sources, flames and sparks. 
    Do not eat, drink or smoke while applying.
    Do not apply before 09:00 and after 16:00 in the winter.
    Although the spreading rate will vary with porosity and type of substrate, for uncoated new surfaces work on 6-8 square metres per litre for the first coat and 10-12 square metres per litre for subsequent coats and when applied to sealed substrates.
  6. Surface Preparation

    New Wood Sand the wooden substrate well and remove all dust.
    Brush apply one coat of NEO Woodcoating (suede) diluted with approximately 10% NEO Mineral Turpentine (mt00).
    Allow to dry 18-24 hours before sanding again.
    Remove all dust.
    Brush apply two more generous coats leaving 24 hours between coats.
    Existing Varnished Surfaces Sand the wooden substrate well and remove all dust.
    If the existing varnished substrate is in a good condition, sand well and apply two coats of NEO Woodcoating (suede).
    Should the existing varnish coating be brittle, flaking, peeling, cracking etc., it must be completely removed:
    o Apply a thick layer of NEO Paint Remover (pr00) on the varnished surface.
    o After 15-20 minutes, lift off the paint remover together with the old varnish using a scraper.
    o Rinse well with warm soapy water to remove all traces of the paint remover.
    When dry, sand well.
    Brush apply one coat of NEO Woodcoating (suede) diluted with approximately 10% NEO Mineral Turpentine (mt00).
    Allow to dry 18-24 hours before sanding again.
    Remove all dust.
    Brush apply two more generous coats leaving 24 hours between coats.
  7. Colour Range and Quantities

    NEO Woodcoating (suede) is available in clear (slightly yellow) only.
    Available in 500ml, 1 litre and 5 litres.
  8. Precautions

    NEO Woodcoating (suede) is highly flammable.
    Use only in well ventilated areas and do not eat, drink or smoke during application.
    The product contains no toxic substances.
  9. Disclaimer

    NEO Paints can not be held liable if the product fails due to improper surface preparation or application.